ADSR release completes - but its not really silent!
-
- Posts: 233
- Joined: 25 Oct 2005 04:06
- Contact:
ADSR release completes - but its not really silent!
Using say the 303-like 7 preset, i wired the output of the amp module into another amp so i could control it with and adsr ( the 303 like presets and some others are oddly without amp envelopes, or even gated on the amp, and trying to use an adsr on the already existing amp module which is being modulated by a stepsequncer doesnt work, when i release the note a little bit of glitchy noise still comes thru) and that works fine...i now have a 303 like synth with an adsr...
ok so i enable the distortion unit and set its type to hard fuzz...then crank the amount and drive to full - and for some reason - even tho im not playing a note - the sound comes thru...the adsr shows its at 0, and this is even wierder - if i turn the bits knob down below about 70% - it stops playing!
Why does the hard fuzz mode allow sound to come thru despite the fact the adsr is released on 0? If i use the amps inbuilt gate option this doesnt happen....it seems as if the adsrs lowest value (which should be absolute silence) is actually just very quiet....i dunno its so odd....
ok so i enable the distortion unit and set its type to hard fuzz...then crank the amount and drive to full - and for some reason - even tho im not playing a note - the sound comes thru...the adsr shows its at 0, and this is even wierder - if i turn the bits knob down below about 70% - it stops playing!
Why does the hard fuzz mode allow sound to come thru despite the fact the adsr is released on 0? If i use the amps inbuilt gate option this doesnt happen....it seems as if the adsrs lowest value (which should be absolute silence) is actually just very quiet....i dunno its so odd....
Last edited by matthewjumpsoffbuildings on 04 Jun 2006 06:52, edited 1 time in total.
-
- Posts: 233
- Joined: 25 Oct 2005 04:06
- Contact:
-
- Posts: 110
- Joined: 01 Oct 2005 03:08
-
- Posts: 233
- Joined: 25 Oct 2005 04:06
- Contact:
-
- Posts: 233
- Joined: 25 Oct 2005 04:06
- Contact:
If amplifiers amp and mod knobs are centered and you modulate the amp knob with a (non inverted) ADSR. Not triggering should result in true silence, and you shouldn't be able to get any sound out nomatter what filter or distortion you apply.
If this happens, it sure sounds like a bug....can you send me the patch ? e.g. as fxp ?
If this happens, it sure sounds like a bug....can you send me the patch ? e.g. as fxp ?
-
- Posts: 110
- Joined: 01 Oct 2005 03:08
-
- Posts: 233
- Joined: 25 Oct 2005 04:06
- Contact:
-
- Posts: 233
- Joined: 25 Oct 2005 04:06
- Contact:
ok heres an fxp - notice the adsr - all good - but turn on the distortion unit and you will see that some signal is still getting past the adsr - even tho it should be silent.
http://freefileupload.net/file.php?file ... -synth.fxp
http://freefileupload.net/file.php?file ... -synth.fxp
-
- Posts: 233
- Joined: 25 Oct 2005 04:06
- Contact:
-
- Posts: 233
- Joined: 25 Oct 2005 04:06
- Contact:
-
- Posts: 233
- Joined: 25 Oct 2005 04:06
- Contact: